English
Русский
Español
العربية
Plate Marking and Punching Machine
There are two hydraulic clamps on the sliding plate, their location can be moved alongside the Axis X so as to adjust different work piece. While in adjustment, loose the screw and press plate, move the clamp by hand to the adequate place, fasten the screw and press plate again. In the vertical direction, the clamp is in the condition of floating. To the joint plate with slight unevenness, they may be arched during punching, and then the clamp will be moved accordingly to avoid the breakage of clamp. A original location device is installed at the left side of the sliding plate, when the hydraulic cylinder push the locating plate at an angle of 90°, the locating surface is just at the same direction to the Axis Y, and form a rectangle with two clamp surfaces (direction of Axis X) to calibrate the original place of joint plate.
The upper and lower jaws of clamp are spliced which are convenient to replace after abrasion.
This drilling unit enjoys compact design, powerful engine and high efficiency.
With the automatic signal transmission device which can send signals automatically when the drill touches the work piece and finishes punching, the drilling machine possesses the empty run fast forward function and instant transfer to processing function when touches with work piece. After finishes drilling, it can be returned with high speed. In other word, during the drilling work, this drill machine does not need to make any adjustment according to the variation of the lengthen of drill bit or the thickness of the plate, as a result, this drill machine can largely diminish the non-operation time to improve the efficiency.
The drilling and drawing force of the main bearing is provided by the gear driven while the feeding power is driven by the hydraulic cylinder.
1. Brief Introduction:
The YJX CNC Hydraulic Connecting Plate Punching Machine is often used in the production of Iron/Steel Towers in the Power transmission and transformation industry and the production of metal structural parts in the construction and bridge industries. It is mainly used for punching, drilling and typing of connecting plates.
2. Machine Model and Configuration:
2.1 Mechanical Part
| No. | Item | YBJ120 |
| 1 | Machine Layout Area | 5*3.5 M |
| 2 | No. of Hosts | 1 Set |
| 3 | No. of Workbench Bases | 1 Set |
| 4 | No. of Y-Slide | 1 Set |
| 5 | No. of X-direction Slide | 1 Set |
| 6 | No. of Clamps | 2 Sets |
| 8 | Pneumatic control system | 1 Set |
| 9 | Hydraulic control system | 1 Set |
| 10 | Buyer Preparation Working | Installation Site-cement foundation, embedded slabs and anchor bolts required by equipment, make the foundation according to the foundation plan provided by the supplier |
2.2 Electric control Part
| 1 | CNC Controller system | PLC control system |
| 2 | Drive System | Panasonic Servo Motor |
3. The main technical parameters of the machine
| No. | Item | YBJ120 |
| 1 | Processing plate size | 1500*800mm |
| 2 | Processing plate thickness | 5-27mm |
| 3 | Punching force | 1200KN |
| 4 | Maximum punching diameter | Φ33mm |
| 5 | Total number of modules | 3 Pcs |
| 6 | Number of punching die | 2 Pcs |
| 7 | Number of print header groups | 1 Group |
| 8 | Prefix | 10 Pcs |
| 9 | Header size | (L*W*H)14*10*19mm |
| 10 | Number of CNC axes | 2 |
| 11 | X, Y axis servo motor power | 2*2KW |
| 12 | X, Y axis feeding speed | 20m/min |
| 13 | Punching speed | 50-55 Times/Min |
| 14 | Total weight of equipment | 6T |
4. Machine working environment
| 1 | Power supply | 3 Phase 4-Wire System |
| 2 | Voltage | 3 Phase 415V±10% |
| 3 | Frequency | 50Hz |
| 4 | Operating Temperature | 0℃-40℃ |
| 5 | Relative Humidity | <90% no condensation |
| 6 | Compressed Air | Pressure: 0.8MPa Flow rate: 0.1m³/min |
5. Machine parts introduction
The equipment is mainly composed of Punching Host Unit, Workbench Moving Unit, Clamp Assembly, Pneumatic System, Electrical System, Hydraulic System, etc.
